1. Home
    2. testo 330i Basic Set

    testo 330i basic set - flue gas analyzer set

    0563 3000 70
  1. Operation independent of measuring location and display of readings via smartphone or tablet and the testo 330i App
  2. Paperless documentation and report creation on site with the testo 330i App
  3. Reliable attachment of the flue gas probe with the testoFix probe holder
  4. Practical accessories, including probes and temperature probe
    5. Everything you need to carry out efficient servicing and commissioning of heating systems using the testo 330i flue gas analyzer – in one compact set.
    The testo 330i flue gas analyzer combines the proven measuring technology of the preceding model testo 330 LL with a revolutionary new method of operation: operation independent of measuring location via smartphone, a sturdy testoFix probe holder and paperless documentation. This instrument embodies the current trends in flue gas measurement.
    The centrepiece of the set is the testo 330i flue gas analyzer with H2-compensated CO sensor. The flue gas analyzer is therefore also approved for the official acceptance testing of heating systems.
    Operation of the flue gas analyzer and the display of readings are implemented independently of the measuring location via the testo 330i App on your smartphone or tablet. Here, you can make adjustments to the measuring instrument, analyze the flue gas values, enter customer data and create measurement protocols. You can then add comments or photos of the system to the protocols, and send them to the customer or your office via e-mail.

    Requirement: iOS 7.1 / Android 4.3 or newer. Mobile end device with Bluetooth 4.0.

    The testo 330i flue gas analyzer also has the following impressive features

    • User-replaceable long-life sensors with a service life of up to 6 years. This saves at least one sensor replacement over the flue gas analyzer's typical useful life
    • TÜV-tested according to 1st German Federal Immission Control Ordinance (BImSchV) and EN 50379, Parts 1-3
    • Integrated draught and gas zeroing without removing the probe. The probe can remain in the flue during zeroing
    • Fresh air dilution upon exceeding a CO threshold value up to 30,000 ppm
    • Fully enclosed, particularly robust plastic housing
    Also included in the set: a modular flue gas sampling probe (180 mm) with a 65 cm long, extra-flexible hose and a 190 mm long combustion air temperature probe.
    The testoFix probe holder is included in the set, which enables the probes to be securely attached to the flue gas duct quickly and easily. This global innovation also serves as a fall-proof suspension system for the testo 330i flue gas analyzer. A mains unit and the practical system case, in which all set components can be stowed away compactly and safely, complete this set.

    •    testo 330i with H2-compensated CO sensor 0632 3000 51
    •    Modular flue gas probe with hose (650 mm) 0600 9780
    •    Combustion air temperature probe (190 mm) 0600 9787
    •    International mains unit 0554 1096
    •    testoFix probe holder for probes with a diameter of 8 mm (0554 3006)
    •    Instrument case for testo 330i, probes and accessories (dimensions: 520 × 130 × 400 mm, WxHxD) 0516 3302

     

    General technical data

    Weight
    720 g (excluding battery)
    Dimensions
    270 x 160 x 57 mm
    Operating temperature
    -5 to +45 °C
    Power supply
    Rech. batt. block 3.7 V / 2.6 Ah; Mains unit 6 V / 1.2 A (optional)
    System requirements
    requires iOS 7.1 or newer; requires Android 4.3 or newer; requires mobile end device with Bluetooth 4.0
    Maximum memory
    500000 readings
    Storage temperature
    -20 to +50 °C

    Differential Pressure - Piezoresistive

    Measuring range
    0 to 300 hPa
    Accuracy
    ±1.5 % of mv (Remaining Range)
    ±1 % of mv (+50.1 to +100.0 hPa)
    ±0.5 hPa (0.0 to +50.0 hPa)
    Resolution
    0.1 hPa

    Flue gas O₂

    Measuring range
    0 to 21 Vol.%
    Accuracy
    ±0.2 Vol.%
    Resolution
    0.1 Vol.%

    Accessories for probes

  5. Accessories for probes
    Hose connection set for separate gas pressure measurement
    Hose connection set for separate gas pressure measurement testo 300, testo 330 LL and testo 320
      :
      0554 1203
    • Accessories for probes
      Differenztemperatur-Set testo
      Differential temperature set consisting of 2 Velcro probes and temperature adaper testo 327
        :
        0554 1208
      • Accessories for probes
        probe stop 6mm steel
        Probe stop 6 mm; steel; with spring clamp and handle; Tmax. 500 °C
          :
          0554 3329
        • Accessories for probes
          Mehrloch-Sondenrohr
          Probe shaft multi-hole; length 300 mm; Ø 8 mm; for mean CO calculation
            :
            0554 5762
          • Accessories for probes
            Probe shaft, length 335 mm, incl. cone
            Probe shaft - length 335 mm, Ø 8 mm, Tmax. 1000°C
              :
              0554 8764
            • Accessories for probes
              Probe shaft
              Probe shaft; length 180 mm; 8 mm; Tmax. 500 °C
                :
                0554 9760
              • Accessories for probes
                Probe shaft
                Probe shaft; length 300 mm; Ø 8 mm; Tmax. 500 °C
                  :
                  0554 9761
                • Accessories for probes
                  flue gas probe
                  Our flexible probe shaft helps you to carry out flue gas measurements even on difficult-to-access measurement apertures. Since the probe shaft is made of very flexible plastic, you can easily bend it, allowing it to be inserted into exhaust flues which are obstructed (e.g. by sloping ceilings).
                    :
                    0554 9770
                  • Accessories for probes
                    clearance-probe-for-O2-supply-air-measurement
                    Dual wall clearance probe for O2 supply air measurement
                      :
                      0632 1260
                    • Accessories for probes
                      No picture available
                      Probe stop 8 mm; steel; with spring clamp and handle; Tmax. 500 °C
                        :
                        0554 3330

                        • Combustion air / temperature

                      • Combustion air / temperature
                        Combustion air temperatur probe
                        Combustion air temperature probe, immersion depth 60 mm
                          :
                          0600 9797
                        • Combustion air / temperature
                          Combustion air temperature probe
                          Combustion air temperature probe with an immersion depth of 190 mm – measuring range: 0 to +100 °C
                            :
                            0600 9787

                            • Probes

                          • Probes
                            Flue gas probe 180mm, 8mm
                            Flue gas probe 180 mm, diameter 8 mm
                              :
                              0600 9780
                            • Probes
                              Flue gas probe 300mm, 8mm
                              Flue gas probe 300 mm, diameter 8 mm
                                :
                                0600 9781
                              • Probes
                                Flue gas probe 180mm, 6mm
                                Flue gas probe 180 mm, diameter 6 mm
                                  :
                                  0600 9782
                                • Probes
                                  Flue gas probe 300mm, 6mm
                                  Flue gas probe 300 mm, diameter 6 mm
                                    :
                                    0600 9783

                                    • Flue gas analysis and flue gas measurement

                                    At the core of the measuring technology of the testo 330i are the two long-life sensors for measuring O2 and CO. An NO sensor is optionally available. With the testo 330i, flue gas and draught are measured in parallel – therefore you always have an overview of all relevant readings on a screen in the testo 330i App.

                                    Differential pressure measurement

                                    You can also use the testo 330i flue gas analyzer to measure the gas supply on gas boilers. Measure the gas flow and gas resting pressure to ensure that a gas boiler can be commissioned properly. In conjunction with the manufacturer's specifications concerning the nozzle pressure, the results of this measurement will enable you to tailor the output of the boiler to the home's actual heat requirement.

                                    O2 supply air measurement

                                    In balanced flue systems, you can use the testo 330i to find out whether there is a leak in the flue gas system. For this, simply measure the O2 content of the combustion air in the dual wall clearance. This way, you can ensure that no flue gas is getting into the combustion air supply. This prevents damage due to condensate or impairment of the combustion process.

                                    • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
                                      Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
                                    • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
                                      The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
                                    • Firmware testo 330i(v2.11, 3.56 MB)
                                      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.
                                      A description and all necessary files can be found under the search term: Update-Kit / Bootloader
                                    • Update-Kit / Bootloader(V1.22, 1.24 MB)
                                      (testo 330 LL | testo 330i | testo 350 Control Unit + Analysis Box | testo 320)
                                      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.