1. Home
    2. testo 330i LX

    testo 330i LX - Advanced flue gas analyzer kit

    0563 3000 71
  1. Operation independent of measuring location, and display of readings via smartphone or tablet using the testo 330i LX app
  2. Paperless documentation and report creation on site, with the testo 330i LX app
  3. Reliable attachment of the flue gas probe with the testoFix probe holder
  4. Robust, completely enclosed plastic housing, for use in harsh environments
    5. The testo 330i LX advanced flue gas analyzer kit will enable you to overcome all the challenges that crop up when commissioning and servicing heating systems.  The testo 330i LX advanced kit contains the flue gas analyzer, a flue gas probe, a temperature probe, and a number of practical accessories.
    At the core of the innovative testo 330i LX flue gas analyzer is the measuring technology of the preceding testo 330 LL models, which have been proven in practice a thousand times over.  The outstanding technical features of this flue gas analyzer, such as its user-replaceable long life sensors, integrated draught and gas zeroing, and CO / fresh air dilution have been combined with a revolutionary new method of operation.
     

    The first remote-controlled flue gas analyzer

    Operation of the testo 330i LX flue gas analyzer and the display of its readings are implemented wirelessly via the testo 330i LX app on your smartphone or tablet.  Therefore, when making adjustments to a system, you always have the readings at hand.  In the app, you can enter customer data, make adjustments to measuring instrument settings, and add comments or photos to measurement protocols on site, and send them to your customer or your office via email.  If you need the results of your work on paper, no problem.

    Requirements:  iOS 7.1 / Android 4.3 or newer.  Mobile end device with Bluetooth 4.0.
     

    Further advantages of the testo 330i LX flue gas analyzer

    • User-replaceable long life sensors with a service life of up to 6 years.  This saves at least one sensor replacement over the instrument's typical useful life.
    • H2-compensated CO measuring cell.  The testo 330i LX is also approved for official acceptance testing of heating systems.
    • TÜV-tested according to the 1st German Federal Immission Control Ordinance (BImSchV) and EN 50379, Parts 1 - 3.
    • Integrated draught and gas zeroing, without removing the probe.  The probe can remain in the flue during zeroing.
    • Fresh air dilution upon exceeding a CO threshold value up to 30,000 ppm.

    Flue gas analyzer kit with practical accessories

    The testo 330i LX advanced flue gas analyzer kit includes the following probes:
     
    • Modular flue gas sampling probe (probe length 7.1 in.), with 25.6 in. long extra-flexible hose
    • Combustion air temperature probe, 7.5 in. long
    The patent pending testoFix probe holder is included in the kit, enabling you to quickly, easily, and securely attach probes to a flue gas duct.  This global innovation also serves as a fallproof suspension system for the testo 330i LX flue gas analyzer.  A mains unit for the measuring instrument, the testo 330i LX Bluetooth, and a robust case for the measuring instrument and accessories complete this kit.

    •    testo 330i LX flue gas analyzer with H2-compensated CO sensor (0632 3000 51)
    •    Modular flue gas probe with hose, 25.6 in. (0600 9781)
    •    International mains unit (0554 1096)
    •    testoFix probe holder for probes, with a diameter of 0.3 in. (0554 3006)
    •    Instrument case for testo 330i LX, probes, and accessories (20.5 × 5.1 × 15.7 in., W × H × D) (0516 3302)

    General technical data

    Weight
    25 oz. (excluding battery) / 720 g (excluding battery)
    Dimensions
    11 x 6 x 2 in. / 270 x 160 x 57 mm
    Operating temperature
    23° to 113 °F / -5 to +45 °C
    Power supply
    Rech. batt. block 3.7 V / 2.6 Ah; Mains unit 6 V / 1.2 A (optional)
    System requirements
    requires iOS 7.1 or newer; requires Android 4.3 or newer; requires mobile end device with Bluetooth 4.0
    Maximum
    500000 readings
    Storage temperature
    -4° to 122 °F / -20 to +50 °C

    Differential Pressure

    Measuring range
    0 to 120 InHâ‚‚O / 0 to 300 hPa
    Accuracy
    ±1.5 % of mv (Remaining Range)
    ±0.2 InH₂O (0.0 to +20.0 InH₂O) / ±0.5 hPa (0.0 to +50.0 hPa)
    ±1 % of mv (+20.0 to +40.0 InH₂O) / ±1 % of mv (+50.1 to +100.0 hPa)
    Resolution
    0.0 InHâ‚‚O / 0.1 hPa

    Flue gas Oâ‚‚

    Measuring range
    0 to 21 Vol.%
    Accuracy
    ±0.2 Vol.%
    Resolution
    0.1 Vol.%

    Differential pressure measurement

    You can use the testo 330i flue gas analyzer to check the gas supply on gas boilers. You can therefore measure gas flow pressure and gas resting pressure in order to ensure that the system can be commissioned. You can also use the data specified by the manufacturer for the nozzle pressure to tailor the appliance output to the heat requirement.

    Flue gas analysis and flue gas measurement

    The testo 330i is equipped with two long-life sensors for measuring O2 and CO and can optionally be upgraded with an NO sensor. Flue gas and draught are measured in parallel, so all relevant flue gas parameters are displayed simultaneously on the smartphone.

    O2 supply air measurement

    In balanced flue systems, you can use the testo 330i flue gas analyzer to check whether there is a leak in the flue gas system. Measure the O2 content of the combustion air in the dual wall clearance to ensure that no flue gas is getting into the combustion air supply, thus preventing damage due to condensate or impairment of the combustion process.

    • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
      Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
    • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
      The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
    • Firmware testo 330i(v2.11, 3.56 MB)
      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.
      A description and all necessary files can be found under the search term: Update-Kit / Bootloader
    • Update-Kit / Bootloader(V1.22, 1.24 MB)
      (testo 330 LL | testo 330i | testo 350 Control Unit + Analysis Box | testo 320)
      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.