1. Home
    2. testo 330i heating engineering set

    testo 330i heating engineering set - Flue gas measurement on gas, oil and solid fuel systems

    0563 3000 75
  1. Included in the set: testo 330i flue gas analyzer, including O2 and CO H2-compensated sensor, Bluetooth interface, mains unit, TÜV-tested modular flue gas probe, combustion air temperature probe
  2. Paperless documentation and report generation on site via smartphone App
  3. Operation independent of measuring location via smartphone App
  4. Completely enclosed plastic housing – particularly robust
    5. Flue gas analysis with no stress, paper or shaky probes – the testo 330i flue gas analyzer with smartphone App operation makes this possible. The smart heating engineering set for measurements on gas, oil and solid fuel systems provides you with the testo 330i flue gas analyzer with O2 and CO H2-compensated sensor, along with additional practical accessories.
    In order to commission and service heating systems as quickly and thoroughly as possible, you need the appropriate flue gas analyzer. The testo 330i combines the proven measuring technology of its predecessor, the testo 330 LL, with smart handling.
     

    The testo 330i: heating engineering set in detail


    testo 330i flue gas analyzer, TÜV-tested according to 1st German Federal Immission Control Ordinance (BImSchV) and EN 50379, Parts 1 to 3:
    • For official acceptance test measurements: the H2-compensated CO sensor means you can also carry out official acceptance test measurements with this version of the testo 330i (CO sensor is H2-compensated up to 30,000 ppm)
    • Smart handling: operation of the analyzer and the display and documentation of readings are implemented wirelessly via the testo 330i App on your smartphone. The flue gas analyzer is really easy to control remotely via Bluetooth, from a distance of up to 5 metres. Once you have finished the measurement, you can add comments or photos to the measurement protocol and send it to your customer or the office via e-mail (requirements: iOS 7.1 / Android 4.3 or later. Mobile terminal device with Bluetooth 4.0)
    • Long-life sensors with a service life of up to 6 years that can be replaced by users. This saves at least one sensor replacement over the instrument's normal operating life
    • Integrated draught and gas zeroing without removing the probe – the probe can remain in the flue during zeroing
    • Fresh air dilution when a CO threshold value is exceeded up to 30,000 ppm
    • Built-in magnets enable the flue gas analyzer to be attached to the burner/boiler quickly
    • 4-year warranty without maintenance contract on the instrument and O2 and CO sensor 
    Modular flue gas probe, TÜV-tested:
    • On the TÜV-tested modular flue gas probe with 300 mm long probe shaft, the flue gas path and temperature channel can easily be connected to the measuring instrument via a practical bayonet lock
    • The probe shaft is really easy to replace, thanks to the quick-change click system on the handle
    • The thermocouple NiCr-Ni, which is integrated in the probe shaft, enables temperature measurement up to 500°C
    Combustion air temperature probe:
    • The combustion air temperature probe can be positioned flexibly, as it has a probe shaft length of 190 mm and a cable length of 2.2 m

    • testo 330i flue gas analyzer with long-life gas sensors, 3 slots and integrated draught and gas zeroing. Including O2 and CO H2-compensated sensor, rechargeable battery and calibration protocol (0632 3000 71)
    • Mains unit for connection to the testo 330i flue gas analyzer (0554 1096)
    • Modular flue gas probe 300 mm; Ø 8 mm; Tmax 500°C; TÜV-tested; hose 2.2 m (0600 9761)
    • Combustion air temperature probe, length 190 mm, including cone for attachment (0600 9787)

    • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
      Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
    • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
      The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
    • Firmware testo 330i(v2.11, 3.56 MB)
      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.
      A description and all necessary files can be found under the search term: Update-Kit / Bootloader
    • Update-Kit / Bootloader(V1.22, 1.24 MB)
      (testo 330 LL | testo 330i | testo 350 Control Unit + Analysis Box | testo 320)
      If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.