1. Home
    2. testo 330i advanced set – flue gas analyzer set

    testo 330i advanced set - flue gas analyzer set

    0563 3000 71
  1. Operation independent of measuring location and display of readings via smartphone or tablet and the testo 330i App
  2. Paperless documentation and report creation on site with the testo 330i App
  3. Reliable attachment of the flue gas probe with the testoFix probe holder
  4. Robust, completely enclosed plastic housing for use in harsh environments
    5. The testo 330i flue gas analyzer advanced set will enable you to overcome all the challenges that crop up when commissioning and servicing heating systems. The testo 330i advanced set contains the flue gas analyzer, a flue gas probe and a temperature probe, along with practical accessories.
    At the core of the innovative testo 330i flue gas analyzer is the measuring technology of the preceding model testo 330 LL, which has been proven in practice a thousand times over. The outstanding technical features of this flue gas analyzer, such as its user-replaceable long-life sensors, integrated draught and gas zeroing or CO/fresh air dilution have been combined with a revolutionary new method of operation.

    The first remote-controlled flue gas analyzer

    Operation of the testo 330i flue gas analyzer and the display of readings are implemented wirelessly via the testo 330i App on your smartphone or tablet. Therefore, when making adjustments to the system, you always have the readings to hand. In the App you can also enter customer data, make adjustments to the measuring instrument settings and add comments or photos to measurement protocols on site and send them to the customer or your office via e-mail. If you need the results of your work on paper – no problem: The advanced set also includes a Bluetooth printer with a mains unit.

    Requirement: iOS 7.1 / Android 4.3 or newer. Mobile end device with Bluetooth 4.0.

    Further advantages of the testo 330i flue gas analyzer

    • User-replaceable long-life sensors with a service life of up to 6 years. This saves at least one sensor replacement over the instrument's typical useful life
    • H2-compensated CO measuring cell. The testo 330i is therefore also approved for the official acceptance testing of heating systems
    • TÜV-tested according to 1st German Federal Immission Control Ordinance (BImSchV) and EN 50379, Parts 1-3
    • Integrated draught and gas zeroing without removing the probe. The probe can remain in the flue during zeroing
    • Fresh air dilution upon exceeding a CO threshold value up to 30,000 ppm

    Flue gas analyzer set with practical accessories

    The testo 330i flue gas analyzer advanced set includes the following probes:
    • Modular flue gas sampling probe (probe length: 180 mm) with 65 cm long, extra-flexible hose
    • Combustion air temperature probe (probe length: 190 mm)
    The patent-pending testoFix probe holder is included in the set, enabling you to quickly and easily attach the probes securely to the flue gas duct. This global innovation also serves as a fall-proof suspension system for the testo 330i flue gas analyzer.
    A mains unit for the measuring instrument, the testo 330i Bluetooth/IRDA printer with mains unit and a robust case for the measuring instrument and accessories complete this set.

    •    testo 330i flue gas analyzer with H2-compensated CO sensor (0632 3000 51)
    •    Modular flue gas probe with hose, 650 mm (0600 9780)
    •    Combustion air temperature probe, 190 mm (0600 9787)
    •    International mains unit (0554 1096)
    •    testoFix probe holder for probes with a diameter of 8 mm (0554 3006)
    •    testo 330i BLUETOOTH®/IRDA printer (0554 0621)
    •    Instrument case for testo 330i, probes and accessories (dimensions: 520 × 130 × 400 mm, W × H × D) (0516 3302)

    General technical data

    Weight
    720 g (excluding battery)
    Dimensions
    270 x 160 x 57 mm
    Operating temperature
    -5 to +45 °C
    Power supply
    Rech. batt. block 3.7 V / 2.6 Ah; Mains unit 6 V / 1.2 A (optional)
    System requirements
    requires iOS 7.1 or newer; requires Android 4.3 or newer; requires mobile end device with Bluetooth 4.0
    Maximum memory
    500000 readings
    Storage temperature
    -20 to +50 °C

    Differential Pressure - Piezoresistive

    Measuring range
    0 to 300 hPa
    Accuracy
    ±1.5 % of mv (Remaining Range)
    ±1 % of mv (+50.1 to +100.0 hPa)
    ±0.5 hPa (0.0 to +50.0 hPa)
    Resolution
    0.1 hPa

    Flue gas O₂

    Measuring range
    0 to 21 Vol.%
    Accuracy
    ±0.2 Vol.%
    Resolution
    0.1 Vol.%

    Accessories for probes

  5. Accessories for probes
    Hose connection set for separate gas pressure measurement
    Hose connection set for separate gas pressure measurement testo 300, testo 330 LL and testo 320
      :
      0554 1203
    • Accessories for probes
      Differenztemperatur-Set testo
      Differential temperature set consisting of 2 Velcro probes and temperature adaper testo 327
        :
        0554 1208
      • Accessories for probes
        probe stop 6mm steel
        Probe stop 6 mm; steel; with spring clamp and handle; Tmax. 500 °C
          :
          0554 3329
        • Accessories for probes
          Mehrloch-Sondenrohr
          Probe shaft multi-hole; length 300 mm; Ø 8 mm; for mean CO calculation
            :
            0554 5762
          • Accessories for probes
            Probe shaft, length 335 mm, incl. cone
            Probe shaft - length 335 mm, Ø 8 mm, Tmax. 1000°C
              :
              0554 8764
            • Accessories for probes
              Probe shaft
              Probe shaft; length 180 mm; 8 mm; Tmax. 500 °C
                :
                0554 9760
              • Accessories for probes
                Probe shaft
                Probe shaft; length 300 mm; Ø 8 mm; Tmax. 500 °C
                  :
                  0554 9761
                • Accessories for probes
                  flue gas probe
                  Our flexible probe shaft helps you to carry out flue gas measurements even on difficult-to-access measurement apertures. Since the probe shaft is made of very flexible plastic, you can easily bend it, allowing it to be inserted into exhaust flues which are obstructed (e.g. by sloping ceilings).
                    :
                    0554 9770
                  • Accessories for probes
                    clearance-probe-for-O2-supply-air-measurement
                    Dual wall clearance probe for O2 supply air measurement
                      :
                      0632 1260
                    • Accessories for probes
                      No picture available
                      Probe stop 8 mm; steel; with spring clamp and handle; Tmax. 500 °C
                        :
                        0554 3330

                        • Combustion air / temperature

                      • Combustion air / temperature
                        Combustion air temperatur probe
                        Combustion air temperature probe, immersion depth 60 mm
                          :
                          0600 9797
                        • Combustion air / temperature
                          Combustion air temperature probe
                          Combustion air temperature probe with an immersion depth of 190 mm – measuring range: 0 to +100 °C
                            :
                            0600 9787

                            • Probes

                          • Probes
                            Flue gas probe 180mm, 8mm
                            Flue gas probe 180 mm, diameter 8 mm
                              :
                              0600 9780
                            • Probes
                              Flue gas probe 300mm, 8mm
                              Flue gas probe 300 mm, diameter 8 mm
                                :
                                0600 9781
                              • Probes
                                Flue gas probe 300mm, 6mm
                                Flue gas probe 300 mm, diameter 6 mm
                                  :
                                  0600 9783

                                  • Differential pressure measurement

                                  You can use the testo 330i flue gas analyzer to check the gas supply on gas boilers. You can therefore measure gas flow pressure and gas resting pressure in order to ensure that the system can be commissioned. You can also use the data specified by the manufacturer for the nozzle pressure to tailor the appliance output to the heat requirement.

                                  Flue gas analysis and flue gas measurement

                                  The testo 330i is equipped with two long-life sensors for measuring O2 and CO and can optionally be upgraded with an NO sensor. Flue gas and draught are measured in parallel, so all relevant flue gas parameters are displayed simultaneously on the smartphone.

                                  O2 supply air measurement

                                  In balanced flue systems, you can use the testo 330i flue gas analyzer to check whether there is a leak in the flue gas system. Measure the O2 content of the combustion air in the dual wall clearance to ensure that no flue gas is getting into the combustion air supply, thus preventing damage due to condensate or impairment of the combustion process.

                                  • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
                                    Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
                                  • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
                                    The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
                                  • Firmware testo 330i(v2.11, 3.56 MB)
                                    If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.
                                    A description and all necessary files can be found under the search term: Update-Kit / Bootloader
                                  • Update-Kit / Bootloader(V1.22, 1.24 MB)
                                    (testo 330 LL | testo 330i | testo 350 Control Unit + Analysis Box | testo 320)
                                    If the firmware update does not start under Windows 8.1 or Windows 10, a new bootloader must be installed on the measuring device once.