Image
    1. Home
    2. testo 380 fine particle measuring system

    testo 380 - Particulate matter measurement system

    0632 3801
  1. The system comprises testo 380 particulate matter measuring instrument and testo 330-2 LL flue gas analyzer
  2. Complete solution for solid fuel, oil and gas systems 
  3. Fully TÜV-tested for limit value levels 1/2 and according to VDI 4206 Sheet 2
    4. With the testo 380 particulate matter measurement system, you can carry out uncomplicated particulate matter measurements directly on site. The completely new method of measurement developed by Testo enables the particulate matter to be monitored and limit values to be enforced. The measurement system is your professional tool for solid fuel, oil and gas systems.
    The constantly rising number of solid fuel systems is leading to a further increase in the emission of particulate matter. The revised version of the 1st German Federal Immission Control Ordinance (BImSchV) presents new challenges for flue gas inspectors, heating engineers and service engineers when it comes to particulate matter measurement.

    testo 380 particulate matter measurement system – complete solution for solid fuel, oil and gas systems

    The testo 380 particulate matter measurement system comprises two system components: the testo 380 particulate matter measuring instrument including particulate matter probe and the testo 330-2 LL as a control centre and flue gas analyzer. This complete system is extremely compact, easy to use and ensures accurate measurements on solid fuel, oil and gas systems.

    Advantages of the testo 380 particulate matter measurement system for particulate matter measurement

    • Suitability permit received for fuels 1-8, levels 1 and 2
    • Measurement system comprising testo 380 particulate matter measuring instrument and testo 330 LL flue gas analyzer
    • The testo 380 particulate matter measuring instrument allows you to carry out effortless and straightforward measurements directly on site
    • testo 330 LL flue gas analyzer: System control centre and flue gas analyzer
    • Parallel measurement of particle matter, O2 and CO in real time
    • Charts used to show all required measuring values for an optimum overview
    • Particularly cost-effective operation and maintenance
    • Effortless handling and easy transportation
    • Fully TÜV-tested for limit value levels 1 and 2 and according to VDI 4206 Sheet 2
    • High-tech in a portable case: measurement of all relevant values with just one probe

    testo 380 particulate matter measurement system incl. testo 380 particulate matter measuring instrument with particulate matter probe and cleaning set, testo 330-2 LL flue gas analyzer with mains unit (incl. Bluetooth, H2-compensated CO cell), modular flue gas probe (length 300 mm, Ø 8 mm), combustion air temperature probe (length 190 mm).

     

    General technical data

    Weight
    7900 g
    Measuring range
    0 to 300 mg/m³
    Accuracy
    acc. VDI 4206-2
    Resolution
    0.1 mg/m³ (>5mg/m³)
    Dimensions
    475 x 360 x 190 mm
    Operating temperature
    +5 to +40 °C
    Product-/housing material
    ABS
    Protection class
    IP40
    Display type
    LCD (Liquid Crystal Display)
    Display function
    shows warm-up phase and operational readiness
    Power supply
    via internal mains unit: 100 V AC/0.45 A to 240 V AC/0.2 A (50 to 60 Hz)
    Maximum memory
    500.000 readings
    Storage temperature
    -20 to +50 °C

    • Instruction manual EasyHeat software(pdf, 3.55 MB)
    • Testo ZIV driver ZIV 2000 for testo 320 and testo 330(v2.1, 2.22 MB)
      Testo ZIV driver in the 2000 version. The Testo ZIV driver is used to connect the testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface Version 2.0 defined by the Zentralverband des Schornsteinfegerhandwerks (Central Association of Chimney Sweeps, ZIV). Please check with the manufacturer of your application program as to whether this interface is supported. If Microsoft .NET Framework 4.0 has not been installed on the computer, it must be downloaded from the Microsoft website and installed on the system.
    • Testo ZIV driver for testo 300, testo 320 and testo 330(v2.3, 64.11 MB)
      The Testo ZIV driver is used to connect the testo 300, testo 320 and testo 330 measuring instruments to an application program (sweeping district administration program) according to the interface defined by the Zentralverband des Schornsteinfegerhandwerks (ZIV, Central Association of Chimney Sweeps) in version 1.0 of 01. August 2012, in version 2.0 of 13. February 2017 as well as version 3.0 from 02. July 2021. Please check with the manufacturer of your application program as to whether this interface is supported.
    • testo 380 Box(V1.17, 1.75 MB)
    • Firmware Update testo 380(63.98 MB)